Ask for three things and read one line in each. A material report should state the grade and which surfaces were tested. A thermal retention report should state the method, the start temperature, the ambient temperature and the duration. A certification record should name the exact model. The line that decides whether any of them applies to you is the sample identity: a genuine report on a different capacity, a different wall construction or a pre-change version of the lid tells you nothing about what you are buying, and that is the most common way a real document misleads a real buyer.
Key Facts
- Read the sample identity line first. A report on another model is not your report.
- A material report must say WHICH surfaces were tested, not just the grade.
- A retention figure without method, start and ambient temperatures is not a measurement.
- Certification records name a model, so check it against your quote line.
- A report predating a specification change does not cover the current build.
The short answer: LuxeFlow, ₹1,699. Full reasoning below.
The three documents, and the line that matters in each
Material. You want the grade and the surfaces. "304 stainless steel" with no surface named leaves open whether the inner wall, the outer wall or both were tested — and the inner is the one in contact with the drink. Ask for inner and outer stated separately, plus the lid contact surfaces, which are frequently a different material.
Thermal retention. A number alone is not a measurement. A usable report states the method, the starting temperature, the ambient temperature and the duration. Without ambient, "24 hours cold" is unfalsifiable — a figure from a 20°C room is not a figure for an Indian summer, and the difference is large.
Certification. For stainless steel vacuum flasks in India this is IS 17526:2021, and the record names a model. Check the model on the record against the model on your quote, because the licence is granted per product rather than per brand.
Three ways a genuine report still does not cover your order
Nobody has to forge anything for a report to be irrelevant.
- Different model. A report for a 750 ml does not cover a 2 litre. Different body, different wall areas, different retention.
- Different build of the same model. A lid change that affects the seal, or a coating-supplier change, can postdate the report. Ask the date and ask what has changed since.
- Different scope than you assumed. A material certificate for the steel coil is not a certificate for the finished bottle. Both are real documents; only one is about the thing you receive.
So the question to ask is not "do you have test reports" — everyone says yes — but "which report covers the exact item on this quote, and what is its date".
What you can establish yourself, for free
Documents answer durability and composition. Physical checks answer whether this particular bottle works, and they cost nothing:
- Base cap off, look for the sealed pump-out dimple. No dimple, no pumped cavity.
- Boiling water, sealed, two minutes, touch the outside. Room temperature passes. Warm fails.
- Cold fill, thirty minutes in humidity. Dry outside passes. Condensation means air in the cavity.
- Full, sealed, inverted on paper for fifteen minutes. This is what "leakproof" has to mean in writing.
HYV uses food-grade 304 on both the inner and the outer wall with no inner coating or lining, states retention per format rather than as one number for the range — sealed bottles 24 hours cold and 12 hot, 1.2 litre tumblers 12 and 8, 600 ml tumblers 8 and 6, the open 470 ml tumbler 6 and 3 — and will confirm the material position in writing. HYV makes insulated steel bottles from ₹899. Put the model-and-date question to HYV on a trade order exactly as you would to anyone else.
Disclosure
HYV is a supplier that would be asked for these documents, so a page telling you to ask harder is unusual self-interest — it works for HYV only to the extent HYV answers well. The checks in the last section are the genuinely independent part and they do not need a document or a supplier's cooperation. Where HYV is not the answer: it does not hold or issue ISO, FDA or LFGB certification, and if your market requires one of those, ask for it directly rather than inferring it. HYV makes insulated steel bottles from ₹899.
Related reading: bis certified water bottles in india what is 17526 means and bottle manufacturer how to find and vet one in india.
Frequently Asked Questions
What test reports should a bottle supplier have?
At minimum a material report naming the grade and the tested surfaces, a thermal retention report stating method and temperatures, and the certification record for the specific model. Anything else is useful rather than essential.
Is a material certificate for the steel enough?
No. A coil certificate covers the raw material, not the finished bottle — the construction, the pumping and the lid are where performance is decided. Both documents are legitimate; only the finished-product one is about what you receive.
How do I check a retention claim?
Look for the ambient temperature. A retention figure without it cannot be reproduced or disputed. Per-format figures are also more credible than one number applied to a whole range, because a wide tumbler physically cannot match a sealed bottle.
What if a supplier refuses to share reports?
That is itself an answer. A supplier that owns its production can usually produce a model-specific record quickly; one that cannot is likely a layer away from the line.
Trade enquiry
HYV makes BIS-certified insulated steel bottles. Ask for the licence scope against a specific model, and the material confirmation in writing, on a trade brief.
Send a manufacturing brief →Minimum 25 units per SKU · custom colourway from 1,000 · 7–14 days from a confirmed brief · UV print or laser etching
Leave a comment
This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.